Product Description
What are the symptoms of a damaged half shaft?
The half shaft is the component that transmits power to the wheels. Without the half shaft, the power cannot be transmitted to the wheels. If the car’s half shaft is damaged, it will cause the car to vibrate abnormally when driving, and will also cause abnormal noises when the car is driving. If the drive shaft is damaged, it needs to be replaced immediately.
If there is a problem with the drive shaft when the vehicle is driving at high speed, it may cause the car tires to fall off or the wheel hub to become out of round. The wheel hub out of roundness will cause the car’s dynamic balance to become unbalanced, causing the car’s high-speed steering wheel to shake. In the vehicle’s transmission system, the half shaft plays an important role and is the shaft that connects the drive wheels and the differential. The inner tie rod ends are generally connected to each other through side gears and splines, and the outer tie rod ends are connected to the wheel hub and flange. The structure of the automobile drive wheel is determined by the structural form of the half shaft. According to the different stress conditions of the half shaft, it can be divided into semi-floating half shaft and fully floating half shaft. It can be seen that the automobile half shaft is the most important factor in the daily driving of the car. An important component, the safe driving of the car depends on the performance of the drive shaft. After long-term torsional fatigue and impact, automobile half shafts are prone to bending, breakage, twisting, skewing, and spline tooth wear. The fractures of automobile half shafts usually have the following morphological types: 1.The spiral of the half-shaft shaft is broken; 2. Mixed cracks and fractures appear in the half-shaft shaft; 3.The splines of the half-shaft are broken; 4.The half-shaft is blue Cracks appear on the disc, and may even fall off in severe cases; 5.Other morphological fractures and cracks in the half shaft.
Product description
HDAG oem -20 2-1 auto spare parts propeller half shaft cardan rear axle reinforced drive shaft for chevrolet niva vaz 2123 2121-21214
Item Name | Auto or car CV JOINT,Universal Joint,CV JOINT INNER OUTER, DRIVE SHAFT, DRIVESHAFT,CV AXLE, JOINT SHAFT ASSEMBLY,CV AXLE JOINT SHAFT, HALF SHAFT, WHEEL BEARING HUB, WHEEL HUB BEARING, WHEEL BEARING | |||||||||||||||||||
OEM/REF NO. | 2 2 2 2 2 2 2 -20 21213 -2203012-1 | |||||||||||||||||||
Car Model | For lada UAZ 2206/3151/3303/3741/9 3741 236571 3160 3163 NIVA VAZ samara moskvich 2141 Tavria 1102 GRANTA LARGUS Vesta X-Ray Kalina PRIORA BA3 Granta Kalina Priora OKA VESTA Gazelle Gazelle Gazel Gazon Kamaz Patriot | |||||||||||||||||||
POSITION | RH/LH/Right/ Left/ Front/Rear | |||||||||||||||||||
MOQ | 150PCS | |||||||||||||||||||
Quality/Product parameters | OEM standard or Design as sample or drawing | |||||||||||||||||||
Payment Terms | T/T, L/C, Credit card, Cash | |||||||||||||||||||
Product Guarantee | 1 Year or 50, TOYOTA : TOYOTA : TOYOTA : 4342 TOYOTA : 4342 TOYOTA : 4342R20 TOYOTA : 4346R30 TOYOTA : 4346S50 TOYOTA : 4346 TOYOTA : 4347S60 TOYOTA : 4347U90 TOYOTA : TOYOTA : TOYOTA : 434708Z033 TOYOTA : 434708Z037 |
NISSAN : 391J10 NISSAN : 391571JJ10 NISSAN : 39157117JJ10 NISSAN : 3910110JJ10 |
NISSAN : 391M615 NISSAN : 391Y10 NISSAN : 391M570 NISSAN : 391N215 NISSAN : 391571M311 NISSAN : 391571M915 NISSAN : 3910140Y10 NISSAN : 391014M570 NISSAN : 391014M575 NISSAN : 391014M771 NISSAN : 3910163Y10 NISSAN : 391016N215 |
MAZDA : G057155J210 NISSAN : 391J171 NISSAN : 391N275 NISSAN : 391J071 NISSAN : 391J915 NISSAN : 391E478 NISSAN : 391012J215 NISSAN : 391014N175 NISSAN : 391014N177 NISSAN : 391014N275 NISSAN : 391015J571 NISSAN : 391016J571 NISSAN : 391016J071 NISSAN : 391016J076 NISSAN : 391016J915 NISSAN : 39101AE415 NISSAN : 39101AU415 NISSAN : 39101AU416 NISSAN : 39101AW110 NISSAN : 39101CX116 NISSAN : 39101WF715 NISSAN : 39101WF716 |
391 | 391M10 TOYOTA : 4347Z035 TOYOTA : 434708Z039 |
374077/374078/374092/7837456/7839615/7837457 | 3920164Y10 | G564-25-5, 8D0498103, 8D0498103A,3B0498103,43145711H | 8D0498099A,8D 0571 15H,8D0498099C,8D 0571 15H | 43420-20380 | 3748103A | 86~88099 | 435711011 | 44105-78B VAG : |
6Q0498099E, 6Q0498099B, 6Q0498099EX | 43403-6, 96564144 ,96396134,512395 |
39211-3U | 39211-BM726 | FD50-25-40XA, FA60-25-40X, FA58-25-50X FA252560XA/FA557160X/FA5822510/FA5822510B/FD54-25-60XA/FD55-25-50XA |
1K0498103C | 8K0498099X,8K0498099,8K0498099D | 17145711 171498UU507 NISSAN : 391V70A NISSAN : 391013U505 NISSAN : 391014V01C NISSAN : 391014V51A NISSAN : 391014V70A NISSAN : 392113U 96348790 |
391 VOLVO : 8111304 VOLVO : 86011 VOLVO : 9122833 VOLVO : 9163595 |
7L 0571 11D,95534995712,95534995710, 7L0498099CX,7L0498099AX | 17145711J,171498099A | 374403/374403/9201725 | 39211-7F | 8K 0571 15C, 8K0498099B, 8K0498099BX | 171498099B,171498099BX | 96273760/96549104/96951692 | 392112F225 | MAZDA : G5712510 MAZDA : G571550X MAZDA : G571560X MAZDA : G565715 OPEL : 374 VAUXHALL : 571 |
391 MAZDA : MD1922510 MAZDA : MD1922510A MAZDA : MD192550X MAZDA : MD257160XB |
|||||||
44014-SP0- OPEL : 374048 OPEL : 374067 OPEL : 37408 OPEL : 374118 OPEL : 374148 OPEL : 374195 OPEL : 90125876 OPEL : 90157212 OPEL : 95718734 OPEL : 9317340 OPEL : 93173430 SAAB : 4242319 |
392114F425 | MD20-25-60X | ||||||||||||||||||
44305SE0J22/44306SE0G12/44305SE0G23/44305SE0G24/44305SE0J20 | A6383342334 | 391KD0A NISSAN : 391KD0A NISSAN : 391019Y015 NISSAN : 39101CNY015 NISSAN : 39211CNHN50 HONDA : 44305S04J60 HONDA : 44305S0A960 HONDA : 44305S0AN60 HONDA : 44305S2H571 HONDA : 44305S2H050 HONDA : 44305S2H950 HONDA : 44305S2H951 HONDA : 44305S2HN50 HONDA : 44305S5AJ50 HONDA : 44305S5AJ60 HONDA : 44305S5AJ61 HONDA : 44305S5AJ62 HONDA : 44305S5C950 HONDA : 44305S5CN50 HONDA : 44305S5CN51 HONDA : 44305S7B950 HONDA : 44305S7C950 HONDA : 44305SOA960 HONDA : 44305SOAN60 HONDA : 44306S0A960 HONDA : 44306S0AN60 HONDA : 44306S2H571 HONDA : 44306S2H950 HONDA : 44306S2H951 HONDA : 44306S5AJ51 HONDA : 44306S5AJ61 HONDA : 44306S5AJ62 HONDA : 44306S5C951 HONDA : 44306S5C952 HONDA : 44306S7B950 HONDA : 44306S7C950 HONDA : 44306SOA960 HONDA : 44306SOAN60 |
49591-1F410 | 44305-SA5-000,44305-688-000,44306-689-601,44306-688-571,44305-688-571 | 4401720,4401727,8200169277,8200169281,8200169285,8200169288,8200196277,8200178624 | 39210-Y02G0 326582 |
FG02-25-500D FG02-25-500E FG02-25-600D FG02-25-600E |
|||||||||||||
44014-SDC-A50,44014-SCA-E01,44014SDCA51, | 9565719/3273.17/3273.18/3273.20/3273.21/3273.23/3273.24/3274.79/3274.80 | 44305-SB2-750,44305-SF4-J21,44306-SK7-571 44305-SA2-960 |
825716110,7700111918,8200064731, | 39100ED005 39100ED00A 39101ED00A 39101ED005 |
GF09-25-50X,GP28-25-50XA/GD36-25-60X | |||||||||||||||
44014-SWE-T00,44014-SWE-T01,44014-SWA-000,44014-SWA-571,44014-SXS-A00 | 3272.00/3272.20/3273.55/3273.64/95598120 | 44305-SB2-982,44306-SB0-571 44571-SH3-J01,44306-SB2-984 |
7701351572,7701351571,7701351484,7701351480,7701351479,7701349938,7701349880,7701349874 |
39100-JX00A 39211-CN000 |
GP34-25-60XD | |||||||||||||||
44014-SDE-T00,44014SDCA00,44306SDETOOL | 3272.06/3273.75 | 44305-SH3-961, 44306-SH3-571, 44305-SE0-000,44571-SH3-960,44011-SH3-G12,44305-SH3-961 | 8200264664,39100-0153R,39101-5451R,6001548720,8200690053,820571122 | 1N00-25-500 | KIA : 0K558-25-50X KIA : 0K558-25-60X |
|||||||||||||||
44305-TL1-E00,44014TA0A00 | 3273.Y7 3272.S5 |
44571SL5N01 44571SS571 44571SS0030 44011SS571 44011SS0030 | 391014946R | 39100-AX000 39211-AY125 39101-AX005 39100-AX005 39101-AX000 |
MAZDA : M 0571 1510 MAZDA : M 0571 1510A MAZDA : M 0571 1500C MAZDA : M 0571 1500D MAZDA : M 0571 1600A MAZDA : M 0571 1600B MAZDA : MD0925500A MAZDA : MD0925600A |
|||||||||||||||
44014-S9A-571,44014-SDC-A50,44014-S9A-571, 44014-SCA-E00,44014-SCA-E01 | 3273.60/3273.62/3273.C7/3274.77/95606802/95646292/96184033 | 44305-SM4-983, 44571-SM4-A01, 44571-SL5-N01,44571-SV4-951,44011-SS0-930, | 77,013,524,157,701,300,000 | 39210-F4125 | MAZDA : G064-25-500 MAZDA : G064-25-600 MAZDA : G564-25-500A MAZDA : G564-25-600A MAZDA : G564-25-60X MAZDA : GR01-25-500 MAZDA : GR01-25-50X MAZDA : GR01-25-600 MAZDA : GR01-25-60X MAZDA : GU01-25-500 MAZDA : GU01-25-50XA MAZDA : GU01-25-50XC MAZDA : GU01-25-600 MAZDA : GU01-25-60XA MAZDA : GU01-25-60XD |
|||||||||||||||
44305-SAA-E00 | 9566722380/1495545080/1496138080/9567582280 | 44571-S07-000,44571SR3J01,44571SR3J02 | 299341X2 | 39100-1KA5B | GG06-25-50XC | |||||||||||||||
HONDA : 44014-SDC-A00 HONDA : 44014-SNG-000 HONDA : 44305-SDC-A00 HONDA : 44305-SEA-000 HONDA : 44305-SNG-571 HONDA : 44306-SDC-A01 HONDA : 44306-SDE-T00 HONDA : 44306-SEA-000 HONDA : 44306-SNG-571 |
1495537080;1495541080;9566722180,9566722180 | 44571SR3J03/44571SR3J53/44571ST7N00/44011S07000/44305SF1G10/44011ST3E00/44571-S07-950/44571-ST3-E50 | 9109186,775712978,775712980,775712998,775712999
|
NISSAN : 39100JA571 NISSAN : 39100JD24B NISSAN : 39100JD52B NISSAN : 39101JD24B NISSAN : 39101JD52B NISSAN : 39211JA00A NISSAN : 39211JD22B NISSAN : C9211JA00A NISSAN : C9211JD22B NISSAN : C92AAJA00A NISSAN : C92AAJD22B NISSAN : C9B11JA00A NISSAN : C9BAAJA00A |
MAZDA : CTA125500 MAZDA : FA8571500A MAZDA : FA8571600B MAZDA : FA8125600B MAZDA : FA8225500A MAZDA : FD8571500B MAZDA : FD8571600A MAZDA : FP0125500C |
|||||||||||||||
44014-SDC-A00,44014-SDC-A00,44014-SDE-T00,44014-SNG-000,44306-SNG-571 | 3272-EX 3272-HY 3272-KW 3273-HQ 3273-KJ |
43460-49125/43460-49165/43460-49315/43470-80013/43470-39545 | 1991909 | NISSAN : 39100-ED100 NISSAN : 39100-ED105 NISSAN : 39100-ED305 NISSAN : 39100-ED805 NISSAN : 39101-ED105 NISSAN : 39101-ED305 NISSAN : 39101-ED805 NISSAN : 39211-ED100 NISSAN : C9211-EL10A |
KIA : 0K2N122520 KIA : KK38825600 |
|||||||||||||||
44014-S6D-E01 | 3272.3C | 43410-12500,43410-57180 | TDJ10571 | 39100-AX000/39100-ED100 | HYUNDAI : 49500-25301 HYUNDAI : 49500-25302 HYUNDAI : 49500-25310 HYUNDAI : 49500-25311 HYUNDAI : 49500-25312 KIA : 49500-25301 KIA : 49500-25302 KIA : 49500-25310 KIA : 49500-25311 KIA : 49500-25312 |
|||||||||||||||
44014-TA0-A00,44305-TA0-J00,44305-TA2-J00,44305-TL1-E00,44305-TL3-000,44306-TA0-J00 | 1481451080/3272.9C/3273.3Q | 43460-19795 | LAND ROVER : RTC6811 LAND ROVER : STC3046 |
4571-M7226 40011-M5626 39100-M7270 39101-M7270 39113-M7275 39112-M7225 |
4950624A00/MB297343/MB297873/MB526582/MB176160/MB176161/MB176865 | |||||||||||||||
44014-S9A-571,44014-SDE-T51, 44014-SMT-G01,44306-SEA-N00,44306S9AN00 | 9619947580 | 43410-57120/43460-19865/43420-12430 | LAND ROVER : STC3051 LAND ROVER : TDJ00571 |
39101-1HS0A | HYUNDAI : 49500-25200 HYUNDAI : 49500-25400 KIA : 49500-25200 KIA : 49500-25400 |
|||||||||||||||
44306-SAA-000,44306-SFA-000,44306-SFB-000,44305-SAA-000 | 9619947580/9619947588/9619947688/9619947680 | 43410-12610, 43410-57130, 43410-12520,43410-0W270 | LAND ROVER : LR060382 LAND ROVER : TDB500110 LAND ROVER : TDJ500030 |
39100CA000 39101-CA100 39211-CA100 39100-CA100 |
49508-22A00 49508-22E00 | |||||||||||||||
44014SD5A51 | 9619947580/9619947588/9619947688/9619947680 | 43430-0K571/43430-0K030/43460-80033 | HONDA : 44305S74E00 HONDA : 44305S74E01 HONDA : 44305S74E51 ROVER : GCV1123 ROVER : TFB000070 |
39100-AX000 39211-AY125 39101-AX005 39100-AX005 39101-AX000 |
MB176872, MB297376, MB297377,MB526456,49500-2D002 | |||||||||||||||
44014-S91-571,44014S9A571,44305S9AN00,44305SCAG00 | CITROEN : 3272QF CITROEN : 3272TH CITROEN : 3272WX CITROEN : 3273QQ CITROEN : 3273TT CITROEN : 3273XR DS : 3272QF DS : 3272TH DS : 3273QQ DS : 3273TT PEUGEOT : 3272QF PEUGEOT : 3272TH PEUGEOT : 3272WX PEUGEOT : 3273QQ PEUGEOT : 3273TT PEUGEOT : 3273XR |
43420-5710/43470-5711/43430-5711 | GCV1194,TDJ100590 | 39211-CG000 39211-CG571 |
MB297438,MB297678,MB526831,MB297696,MB526473 |
/* March 10, 2571 17:59:20 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1
After-sales Service: | Three Years |
---|---|
Condition: | New |
Color: | OEM Standard |
Certification: | CE, ISO, ISO/Ts16949 |
Type: | C.V. Joint |
Application Brand: | Nissan, Iveco, Toyota, Ford, Lada Mitsubishi FIAT Opel Peugeot Renault Citroen |
Customization: |
Available
| Customized Request |
---|
How do cardan shafts ensure efficient power transfer while maintaining balance?
Cardan shafts are designed to ensure efficient power transfer while maintaining balance between the driving and driven components. They employ various mechanisms and features that contribute to both aspects. Let’s explore how cardan shafts achieve efficient power transfer and balance:
1. Universal Joints:
– Cardan shafts utilize universal joints, also known as U-joints, to transmit torque from the driving component to the driven component. Universal joints consist of a cross-shaped yoke with needle bearings at each end. These needle bearings allow the joints to pivot and accommodate angular misalignment between the driving and driven components. By allowing for flexibility in movement, universal joints ensure efficient power transfer even when the components are not perfectly aligned, minimizing energy losses and maintaining balance.
2. Misalignment Compensation:
– Cardan shafts are designed to compensate for misalignment between the driving and driven components. The universal joints, along with slip yokes and telescopic sections, allow the shaft to adjust its length and accommodate variations in alignment. This misalignment compensation capability ensures that the cardan shaft can transmit power smoothly and efficiently, reducing stress on the components and maintaining balance during operation.
3. Balanced Design:
– Cardan shafts are engineered with a balanced design to minimize vibration and maintain smooth operation. The shaft tubes are typically symmetrically constructed, and the universal joints are positioned to distribute the mass evenly. This balanced design helps to reduce vibration and minimize the occurrence of unbalanced forces that can negatively impact power transfer and overall system performance. By maintaining balance, cardan shafts contribute to efficient power transmission and improve the lifespan of the components involved.
4. High-Quality Materials and Manufacturing:
– The materials used in the construction of cardan shafts, such as steel or aluminum alloy, are carefully selected for their strength, durability, and ability to maintain balance. High-quality materials ensure that the shafts can withstand the torque and operational stresses without deformation or failure, promoting efficient power transfer. Additionally, precise manufacturing processes and quality control measures are employed to ensure that the cardan shafts are accurately balanced during production, further enhancing their efficiency and balance.
5. Regular Maintenance and Inspection:
– To ensure continued efficient power transfer and balance, regular maintenance and inspection of cardan shafts are essential. This includes periodic lubrication of the universal joints, checking for wear or damage, and addressing any misalignment issues. Regular maintenance helps to preserve the balance of the shaft and ensures optimal performance and longevity.
Overall, cardan shafts ensure efficient power transfer while maintaining balance through the use of universal joints for torque transmission, misalignment compensation mechanisms, balanced design, high-quality materials, and regular maintenance. By incorporating these features, cardan shafts contribute to the smooth operation, reliability, and longevity of various applications in automotive, industrial, and other sectors that rely on efficient power transmission.
Can you provide real-world examples of vehicles and machinery that use cardan shafts?
Cardan shafts are widely used in various vehicles and machinery across different industries. They are employed in applications where torque transmission, power distribution, and flexibility are crucial. Here are some real-world examples of vehicles and machinery that utilize cardan shafts:
1. Automotive Vehicles:
– Cars, trucks, and SUVs: Cardan shafts are commonly found in rear-wheel drive (RWD) and four-wheel drive (4WD) vehicles. They connect the transmission or transfer case to the rear differential or front differential, respectively, enabling torque transmission to the wheels. Examples include sedans, pickup trucks, and SUVs like Jeep Wrangler, Ford F-150, and Toyota Land Cruiser.
– Buses and commercial vehicles: Cardan shafts are used in buses and commercial vehicles that have rear-wheel drive or all-wheel drive configurations. They transmit torque from the engine or transmission to the rear axle or multiple axles. Examples include city buses, coaches, and delivery trucks.
2. Off-Road and Utility Vehicles:
– Off-road vehicles: Many off-road vehicles, such as off-road trucks, SUVs, and all-terrain vehicles (ATVs) utilize cardan shafts. These shafts provide the necessary torque transfer and power distribution to all wheels for improved traction and off-road capabilities. Examples include the Land Rover Defender, Jeep Wrangler Rubicon, and Yamaha Grizzly ATV.
– Agricultural machinery: Farm equipment like tractors and combine harvesters often employ cardan shafts to transmit power from the engine to various attachments such as mowers, balers, and harvesters. The shafts enable efficient power distribution and flexibility for different agricultural tasks.
– Construction and mining machinery: Equipment used in construction and mining applications, such as excavators, loaders, and bulldozers, utilize cardan shafts to transfer power from the engine or transmission to the different components of the machinery. These shafts enable power distribution and torque transmission to various attachments, allowing for efficient operation in demanding environments.
3. Industrial Machinery:
– Manufacturing machinery: Cardan shafts are used in industrial equipment such as conveyors, mixers, and rotary equipment. They provide torque transmission and power distribution within the machinery, enabling efficient operation and movement of materials.
– Paper and pulp industry: Cardan shafts are employed in paper and pulp processing machinery, including paper machines and pulp digesters. These shafts facilitate power transmission and torque distribution to various parts of the machinery, contributing to smooth operation and high productivity.
– Steel and metal processing machinery: Equipment used in steel mills and metal processing facilities, such as rolling mills, extruders, and coil winding machines, often utilize cardan shafts. These shafts enable power transmission and torque distribution to the different components involved in metal forming, shaping, and processing.
These examples represent just a few of the many applications where cardan shafts are employed. Their versatility, durability, and ability to handle torque transmission and power distribution make them essential components in a wide range of vehicles and machinery across industries.
What benefits do cardan shafts offer for different types of vehicles and equipment?
Cardan shafts, also known as propeller shafts or drive shafts, offer numerous benefits for different types of vehicles and equipment. Their versatile design and functionality make them an essential component in various applications. Here are the key benefits that cardan shafts provide for different types of vehicles and equipment:
1. Efficient Power Transmission:
– Cardan shafts ensure efficient power transmission from the engine or power source to the wheels or driven components. In vehicles, such as cars, trucks, and buses, cardan shafts transmit torque from the gearbox or transmission to the differential, enabling the wheels to rotate and propel the vehicle forward. In equipment and machinery, cardan shafts transfer rotational power from the power source, such as an engine or motor, to driven components like pumps, conveyors, or generators. By efficiently transmitting power, cardan shafts contribute to the overall performance and productivity of vehicles and equipment.
2. Flexibility and Misalignment Compensation:
– Cardan shafts offer flexibility and the ability to compensate for misalignment between the driving and driven components. This flexibility is crucial in vehicles and equipment where the engine or power source may not be directly aligned with the wheels or driven machinery. Cardan shafts incorporate universal joints at each end, allowing for angular misalignment and accommodating variations in the relative positions of the components. This feature ensures smooth power transmission, reduces stress on the drivetrain, and enhances the overall maneuverability and performance of vehicles and equipment.
3. Adaptability to Variable Configurations:
– Cardan shafts are adaptable to variable configurations and adjustable setups. In vehicles, they can accommodate changes in the wheelbase or suspension system, allowing for different vehicle sizes and configurations. For example, in trucks with multiple axles, cardan shafts can be adjusted to compensate for varying distances between the axles. In equipment and machinery, cardan shafts can be designed with telescopic sections or sliding splines, enabling length adjustment to accommodate changes in the distance between the power source and driven components. This adaptability makes cardan shafts suitable for a wide range of vehicle and equipment configurations.
4. Vibration Damping and Smooth Operation:
– Cardan shafts contribute to vibration damping and enable smooth operation in vehicles and equipment. The universal joints in cardan shafts help absorb and dampen vibrations that may arise from the power source or drivetrain. By allowing slight angular deflection and compensating for misalignment, cardan shafts reduce the transmission of vibrations to the vehicle or equipment, resulting in a smoother and more comfortable ride for passengers or operators. Additionally, the balanced design of cardan shafts minimizes vibration-induced wear and extends the lifespan of associated components.
5. Safety and Protection:
– Cardan shafts incorporate safety features to ensure the protection of both the vehicle or equipment and the operator. For example, in vehicles, cardan shafts often have shielding or guards to prevent contact with rotating components, reducing the risk of accidents or injuries. In some applications, cardan shafts may also include safety mechanisms such as shear pins or torque limiters. These features are designed to protect the shaft and other components from damage by shearing or disengaging in the event of overload or excessive torque, preventing costly repairs and downtime.
6. Suitable for Various Applications:
– Cardan shafts find applications in a wide range of vehicles and equipment across different industries. In the automotive sector, they are used in passenger cars, commercial vehicles, buses, and off-road vehicles to transmit power to the wheels. In the agricultural industry, cardan shafts connect tractors to various implements, such as mowers, balers, or tillers. In the construction and mining sectors, they are employed in machinery like excavators, loaders, and crushers to transfer power to different components. The versatility of cardan shafts makes them well-suited for various applications, providing reliable power transmission and motion.
In summary, cardan shafts offer several benefits for different types of vehicles and equipment. They ensure efficient power transmission, flexibility, and misalignment compensation, adaptability to variable configurations, vibration damping, and smooth operation. Additionally, they incorporate safety features and are suitable for a wide range of applications in automotive, agricultural, construction, and other industries. Cardan shafts play a vital role in enhancing the performance, maneuverability, and safety of vehicles and equipment, contributing to overall productivity and reliability.
editor by CX 2024-02-20
China wholesaler Gjf Axle Assy Transmission Parts CV Joint for Outlander at 4WD 2003-2005 drive shaft assembly parts
Product Description
Product Description
1.We are manufacturer of cv drive shaft,cv axle, cv joint and cv boot, we have more than 20-years experience in producing and selling auto parts.
2.We have strict quality control, the quality of our products is very good.
3.We are professional in different market around the world.
4.The reviews our customers given us are very positive, we have confidence in our products.
5.OEM/ODM is available, meet your requirements well.
6.Large warehouse, huge stocks!!! friendly for those customers who want some quantity.
7.Ship products out very fastly, we have stock.
Product Name | CV JOINT | Material | 42CrMo alloy steel |
Car fitment | Mitsubishi | Warranty | 12 months |
Model | Outlander AT 4wd 2003-2005 | Place of origin | ZHangZhoug, China |
Certification | SGS/TUV/ISO | MOQ | 4 PCS |
Transportation | Express/ by sea/ by air/ by land | Delivery time | 7-15 days |
OEM/ODM | Yes | Brand | GJF |
Advantages | large stocks/ deliver fastly/ strict quality supervision | Payment | L/C,T/T,western Union,Cash,PayPal |
Sample service | Depends on the situation of stock | Weight | About 9KG |
Detailed Photos
Customer Review
Packaging & Shipping
FAQ
After-sales Service: | 12 Months |
---|---|
Condition: | New |
Color: | Black |
Certification: | CE, DIN, ISO |
Type: | C.V. Joint |
Application Brand: | Mitsubishi |
Samples: |
US$ 16.19/Piece
1 Piece(Min.Order) | |
---|
Customization: |
Available
| Customized Request |
---|
What is a drive shaft?
If you notice a clicking noise while driving, it is most likely the driveshaft. An experienced auto mechanic will be able to tell you if the noise is coming from both sides or from one side. If it only happens on one side, you should check it. If you notice noise on both sides, you should contact a mechanic. In either case, a replacement driveshaft should be easy to find.
The drive shaft is a mechanical part
A driveshaft is a mechanical device that transmits rotation and torque from the engine to the wheels of the vehicle. This component is essential to the operation of any driveline, as the mechanical power from the engine is transmitted to the PTO (power take-off) shaft, which hydraulically transmits that power to connected equipment. Different drive shafts contain different combinations of joints to compensate for changes in shaft length and angle. Some types of drive shafts include connecting shafts, internal constant velocity joints, and external fixed joints. They also contain anti-lock system rings and torsional dampers to prevent overloading the axle or causing the wheels to lock.
Although driveshafts are relatively light, they need to handle a lot of torque. Torque applied to the drive shaft produces torsional and shear stresses. Because they have to withstand torque, these shafts are designed to be lightweight and have little inertia or weight. Therefore, they usually have a joint, coupling or rod between the two parts. Components can also be bent to accommodate changes in the distance between them.
The drive shaft can be made from a variety of materials. The most common material for these components is steel, although alloy steels are often used for high-strength applications. Alloy steel, chromium or vanadium are other materials that can be used. The type of material used depends on the application and size of the component. In many cases, metal driveshafts are the most durable and cheapest option. Plastic shafts are used for light duty applications and have different torque levels than metal shafts.
It transfers power from the engine to the wheels
A car’s powertrain consists of an electric motor, transmission, and differential. Each section performs a specific job. In a rear-wheel drive vehicle, the power generated by the engine is transmitted to the rear tires. This arrangement improves braking and handling. The differential controls how much power each wheel receives. The torque of the engine is transferred to the wheels according to its speed.
The transmission transfers power from the engine to the wheels. It is also called “transgender”. Its job is to ensure power is delivered to the wheels. Electric cars cannot drive themselves and require a gearbox to drive forward. It also controls how much power reaches the wheels at any given moment. The transmission is the last part of the power transmission chain. Despite its many names, the transmission is the most complex component of a car’s powertrain.
The driveshaft is a long steel tube that transmits mechanical power from the transmission to the wheels. Cardan joints connect to the drive shaft and provide flexible pivot points. The differential assembly is mounted on the drive shaft, allowing the wheels to turn at different speeds. The differential allows the wheels to turn at different speeds and is very important when cornering. Axles are also important to the performance of the car.
It has a rubber boot that protects it from dust and moisture
To keep this boot in good condition, you should clean it with cold water and a rag. Never place it in the dryer or in direct sunlight. Heat can deteriorate the rubber and cause it to shrink or crack. To prolong the life of your rubber boots, apply rubber conditioner to them regularly. Indigenous peoples in the Amazon region collect latex sap from the bark of rubber trees. Then they put their feet on the fire to solidify the sap.
it has a U-shaped connector
The drive shaft has a U-joint that transfers rotational energy from the engine to the axle. Defective gimbal joints can cause vibrations when the vehicle is in motion. This vibration is often mistaken for a wheel balance problem. Wheel balance problems can cause the vehicle to vibrate while driving, while a U-joint failure can cause the vehicle to vibrate when decelerating and accelerating, and stop when the vehicle is stopped.
The drive shaft is connected to the transmission and differential using a U-joint. It allows for small changes in position between the two components. This prevents the differential and transmission from remaining perfectly aligned. The U-joint also allows the drive shaft to be connected unconstrained, allowing the vehicle to move. Its main purpose is to transmit electricity. Of all types of elastic couplings, U-joints are the oldest.
Your vehicle’s U-joints should be inspected at least twice a year, and the joints should be greased. When checking the U-joint, you should hear a dull sound when changing gears. A clicking sound indicates insufficient grease in the bearing. If you hear or feel vibrations when shifting gears, you may need to service the bearings to prolong their life.
it has a slide-in tube
The telescopic design is a modern alternative to traditional driveshaft designs. This innovative design is based on an unconventional design philosophy that combines advances in material science and manufacturing processes. Therefore, they are more efficient and lighter than conventional designs. Slide-in tubes are a simple and efficient design solution for any vehicle application. Here are some of its benefits. Read on to learn why this type of shaft is ideal for many applications.
The telescopic drive shaft is an important part of the traditional automobile transmission system. These driveshafts allow linear motion of the two components, transmitting torque and rotation throughout the vehicle’s driveline. They also absorb energy if the vehicle collides. Often referred to as foldable driveshafts, their popularity is directly dependent on the evolution of the automotive industry.
It uses a bearing press to replace worn or damaged U-joints
A bearing press is a device that uses a rotary press mechanism to install or remove worn or damaged U-joints from a drive shaft. With this tool, you can replace worn or damaged U-joints in your car with relative ease. The first step involves placing the drive shaft in the vise. Then, use the 11/16″ socket to press the other cup in far enough to install the clips. If the cups don’t fit, you can use a bearing press to remove them and repeat the process. After removing the U-joint, use a grease nipple Make sure the new grease nipple is installed correctly.
Worn or damaged U-joints are a major source of driveshaft failure. If one of them were damaged or damaged, the entire driveshaft could dislocate and the car would lose power. Unless you have a professional mechanic doing the repairs, you will have to replace the entire driveshaft. Fortunately, there are many ways to do this yourself.
If any of these warning signs appear on your vehicle, you should consider replacing the damaged or worn U-joint. Common symptoms of damaged U-joints include rattling or periodic squeaking when moving, rattling when shifting, wobbling when turning, or rusted oil seals. If you notice any of these symptoms, take your vehicle to a qualified mechanic for a full inspection. Neglecting to replace a worn or damaged u-joint on the driveshaft can result in expensive and dangerous repairs and can cause significant damage to your vehicle.
editor by CX 2023-06-12
China Die Forging Alloy Steel Light Truck Spare Parts Drive Axle Driveshaft Boots drive shaft carrier bearing
Product Description
one
Products
Identify: Die forging alloy steel gentle truck spare areas travel axle driveshaft boots
Content: 40CrMo
Fat: From .2kg-5kg
Packing: wood scenario
Min purchase: 1000pcs
Customized production is accessible as your drawings or sample.
Procedure | Die Forging | |
Content | Stainless Steel, Carbon Metal, Alloy Steel | |
Bodyweight | 0.1Kg~20Kg | |
Warmth Remedy | Quenching, Annealing,Tempering,Normalizing, Quenching and Tempering | |
Testing instrument | composition testing | Spectrometer, Metallographic microscope |
Overall performance tests | Hardness tester, Tensile screening device | |
Size Measuring | CMM,Micrometer, Vernier Caliper, Depth Caliper, feeler gauge | |
Thread Gauge , Top Gauge | ||
Roughness | Ra1.6~Ra6.3 | |
Machining Tools | CNC Middle , CNC Machines, Turning, Drilling, Milling, dull equipment,Grinding Devices, | |
Wire EDM,Laser Chopping&Welding, Plasma Reducing &Welding, EDM etc. | ||
High quality manage | Sampling inspection of uncooked components and semi-completed items, one hundred% Inspection of finished products | |
Surface Treatment method | Shot Blast , Powder Coating, Sharpening, Galvanized , Chrome Plated | |
Generation Potential | 60000T / Many years | |
Lead Time | Normally thirty – forty five Days. | |
Payment Phrases | T/T , L/C | |
Material Normal | ASTM , AISI , DIN , BS, JIS, GB, | |
Certification | ISO9001:2008, IATF16949:2016 |
two
Products High quality Management
Quality management require the inspection and management of incoming resources, creation procedures, and finished items.
The quality management approach consists of,
one First of all, the incoming uncooked supplies with random sampling are analyzed by metallographic microscope to make sure that the chemical composition fulfills the generation specifications
2 Then In the generation procedure, there are QC staffs well timed sampling make certain that the merchandise are free of flaws in the production method, and to coordinate and handle any irregular high quality concerns could be occurred.
three The final step of manufacturing approach is magnetic particle flaw detector of the steel components to detect it’s concealed crack or other defects.
four All the completed metallic areas is sampled in proportion and sent to the laboratory for various mechanical overall performance checks and dimensions measurement, and the surface area good quality is manually a hundred% inspected.
The pertinent screening equipment images are as pursuing:
3
High quality Management Technique Manage:
We strictly carry out system management accordance with iso9001 and ts16949 high quality specifications. And 5S lean creation administration is implemented on the manufacturing website.
The creation administration website as subsequent:
4
Our Rewards:
Manufacturer
Our mother or father business, HiHangZhou Team, is a planet-renowned higher-conclude machinery producing organization with 40 domestic subsidiaries and branches and 8 overseas production vegetation. Has lengthy-term encounter and great track record in cooperation with globe-renowned enterprises.
Engineering
We have a comprehensive manufacturing procedure and equipment investigation and improvement abilities for ferrous metals forming. Much more than 25 many years of generation encounter in forging products and casting equipment companies, make us a lot more totally get all the overall performance of every single gear. One particular-3rd of our firm’s personnel are technician and R&D personnel, making sure that substantial-quality items are created with large effectiveness.
Service
We can supply custom made and common production services with a number of manufacturing procedure integrations. The quality and shipping of goods can be entirely assured, and the capability to connect swiftly and properly.
Culture
The unique company tradition can give complete engage in to the potential of people and give a powerful vitality for the sustainable development of the organization.
Social duty
Our organization strictly implements lower-carbon environmental security, energy-preserving and emission-reduction generation, and is a benchmark business in nearby area.
5
Firm Culture
Our Eyesight
To turn into 1 of the major companies
Our Mission
To turn into a platform for personnel to comprehend their aspiration
To turn out to be 1 of the reworking and upgrading pacemaker of Chinese enterprises
To established the nationwide makes with satisfaction
Our Perception
Strive to create the company into an perfect system for business owners to understand their self-value and contribute to the culture
Values
Improvement is innovation, everyone can innovate
innovation influenced and failures tolerated
6
FAQ
1.
Q: Are you a buying and selling business or a manufacturer?
A: Obviously we are a producer of forging items, casting products and also have a higher level of machining abilities.
two.
Q: What sequence merchandise do your have?
A: We are largely engaged in forming processing of ferrous metals, which includes processing by casting , forging and machining. As you know, this sort of equipment areas can be noticed in different industries of gear producing.
three
Q: Do you give samples? is it cost-free?
A: Indeed, we frequently offer samples according to the standard follow, but we also need customers to give a freight spend-by-account amount to present mutual CZPT of cooperation.
four
Q: Is OEM available?
A: Yes, OEM is available.
five
Q: What is actually your high quality ensure?
A: We insist that the survival of the company ought to rely on the goods top quality steady enhancement, without which we can not survive for extended. We have out strictly product top quality management for each method from incoming supplies, production approach to finished merchandise by means of innovative detection instrument and gear. We also invite independent 3rd functions to certify our high quality and administration methods. Until now we have passed ISO/TS16949 and SGS certification .
6
Q. How about the Packing?
A: We typically use the iron box, or wooden case, also it can be customized in accordance to customer’s calls for.
seven
Q: What is your minimum order amount?
A: Indeed, we require all international orders to have an bare minimum get amount. The quantity is up to the specific products attribute or residence this sort of as the content, bodyweight, construction etc.
eight
Q: What is the direct time?
A: Generally our forging items and casting products want to make new dies or molds, the time of producing new dies or molds and samples within thirty-45 days, and the large batch creation time in thirty-forty five days. it is also in accordance to the parts structural complexity and quantity.
nine
Q: What sorts of payment approaches do you accept?
A: You can make the payment by T/T or L/C. 30% deposit in progress, 70% balance from the duplicate of B/L.
Certification
/ Piece | |
1,000 Pieces (Min. Order) |
###
Processing Object: | Metal |
---|---|
Molding Style: | Forging |
Molding Technics: | Pressure Casting |
Application: | Agricultural Machinery Parts |
Material: | Steel |
Heat Treatment: | Tempering |
###
Samples: |
US$ 20/Piece
1 Piece(Min.Order) |
---|
###
Customization: |
---|
###
Process | Die Forging | |
Material | Stainless Steel, Carbon Steel, Alloy Steel | |
Weight | 0.1Kg~20Kg | |
Heat Treatment | Quenching, Annealing,Tempering,Normalizing, Quenching and Tempering | |
Testing instrument | composition testing | Spectrometer, Metallographic microscope |
Performance testing | Hardness tester, Tensile testing machine | |
Size Measuring | CMM,Micrometer, Vernier Caliper, Depth Caliper, feeler gauge | |
Thread Gauge , Height Gauge | ||
Roughness | Ra1.6~Ra6.3 | |
Machining Equipment | CNC Center , CNC Machines, Turning, Drilling, Milling, boring machine,Grinding Machines, | |
Wire EDM,Laser Cutting&Welding, Plasma Cutting &Welding, EDM etc. | ||
Quality control | Sampling inspection of raw materials and semi-finished products, 100% Inspection of finished products | |
Surface Treatment | Shot Blast , Powder Coating, Polishing, Galvanized , Chrome Plated | |
Production Capacity | 60000T / Years | |
Lead Time | Normally 30 – 45 Days. | |
Payment Terms | T/T , L/C | |
Material Standard | ASTM , AISI , DIN , BS, JIS, GB, | |
Certification | ISO9001:2008, IATF16949:2016 |
/ Piece | |
1,000 Pieces (Min. Order) |
###
Processing Object: | Metal |
---|---|
Molding Style: | Forging |
Molding Technics: | Pressure Casting |
Application: | Agricultural Machinery Parts |
Material: | Steel |
Heat Treatment: | Tempering |
###
Samples: |
US$ 20/Piece
1 Piece(Min.Order) |
---|
###
Customization: |
---|
###
Process | Die Forging | |
Material | Stainless Steel, Carbon Steel, Alloy Steel | |
Weight | 0.1Kg~20Kg | |
Heat Treatment | Quenching, Annealing,Tempering,Normalizing, Quenching and Tempering | |
Testing instrument | composition testing | Spectrometer, Metallographic microscope |
Performance testing | Hardness tester, Tensile testing machine | |
Size Measuring | CMM,Micrometer, Vernier Caliper, Depth Caliper, feeler gauge | |
Thread Gauge , Height Gauge | ||
Roughness | Ra1.6~Ra6.3 | |
Machining Equipment | CNC Center , CNC Machines, Turning, Drilling, Milling, boring machine,Grinding Machines, | |
Wire EDM,Laser Cutting&Welding, Plasma Cutting &Welding, EDM etc. | ||
Quality control | Sampling inspection of raw materials and semi-finished products, 100% Inspection of finished products | |
Surface Treatment | Shot Blast , Powder Coating, Polishing, Galvanized , Chrome Plated | |
Production Capacity | 60000T / Years | |
Lead Time | Normally 30 – 45 Days. | |
Payment Terms | T/T , L/C | |
Material Standard | ASTM , AISI , DIN , BS, JIS, GB, | |
Certification | ISO9001:2008, IATF16949:2016 |
What is a drive shaft?
If you notice a clicking noise while driving, it is most likely the driveshaft. An experienced auto mechanic will be able to tell you if the noise is coming from both sides or from one side. If it only happens on one side, you should check it. If you notice noise on both sides, you should contact a mechanic. In either case, a replacement driveshaft should be easy to find.
The drive shaft is a mechanical part
A driveshaft is a mechanical device that transmits rotation and torque from the engine to the wheels of the vehicle. This component is essential to the operation of any driveline, as the mechanical power from the engine is transmitted to the PTO (power take-off) shaft, which hydraulically transmits that power to connected equipment. Different drive shafts contain different combinations of joints to compensate for changes in shaft length and angle. Some types of drive shafts include connecting shafts, internal constant velocity joints, and external fixed joints. They also contain anti-lock system rings and torsional dampers to prevent overloading the axle or causing the wheels to lock.
Although driveshafts are relatively light, they need to handle a lot of torque. Torque applied to the drive shaft produces torsional and shear stresses. Because they have to withstand torque, these shafts are designed to be lightweight and have little inertia or weight. Therefore, they usually have a joint, coupling or rod between the two parts. Components can also be bent to accommodate changes in the distance between them.
The drive shaft can be made from a variety of materials. The most common material for these components is steel, although alloy steels are often used for high-strength applications. Alloy steel, chromium or vanadium are other materials that can be used. The type of material used depends on the application and size of the component. In many cases, metal driveshafts are the most durable and cheapest option. Plastic shafts are used for light duty applications and have different torque levels than metal shafts.
It transfers power from the engine to the wheels
A car’s powertrain consists of an electric motor, transmission, and differential. Each section performs a specific job. In a rear-wheel drive vehicle, the power generated by the engine is transmitted to the rear tires. This arrangement improves braking and handling. The differential controls how much power each wheel receives. The torque of the engine is transferred to the wheels according to its speed.
The transmission transfers power from the engine to the wheels. It is also called “transgender”. Its job is to ensure power is delivered to the wheels. Electric cars cannot drive themselves and require a gearbox to drive forward. It also controls how much power reaches the wheels at any given moment. The transmission is the last part of the power transmission chain. Despite its many names, the transmission is the most complex component of a car’s powertrain.
The driveshaft is a long steel tube that transmits mechanical power from the transmission to the wheels. Cardan joints connect to the drive shaft and provide flexible pivot points. The differential assembly is mounted on the drive shaft, allowing the wheels to turn at different speeds. The differential allows the wheels to turn at different speeds and is very important when cornering. Axles are also important to the performance of the car.
It has a rubber boot that protects it from dust and moisture
To keep this boot in good condition, you should clean it with cold water and a rag. Never place it in the dryer or in direct sunlight. Heat can deteriorate the rubber and cause it to shrink or crack. To prolong the life of your rubber boots, apply rubber conditioner to them regularly. Indigenous peoples in the Amazon region collect latex sap from the bark of rubber trees. Then they put their feet on the fire to solidify the sap.
it has a U-shaped connector
The drive shaft has a U-joint that transfers rotational energy from the engine to the axle. Defective gimbal joints can cause vibrations when the vehicle is in motion. This vibration is often mistaken for a wheel balance problem. Wheel balance problems can cause the vehicle to vibrate while driving, while a U-joint failure can cause the vehicle to vibrate when decelerating and accelerating, and stop when the vehicle is stopped.
The drive shaft is connected to the transmission and differential using a U-joint. It allows for small changes in position between the two components. This prevents the differential and transmission from remaining perfectly aligned. The U-joint also allows the drive shaft to be connected unconstrained, allowing the vehicle to move. Its main purpose is to transmit electricity. Of all types of elastic couplings, U-joints are the oldest.
Your vehicle’s U-joints should be inspected at least twice a year, and the joints should be greased. When checking the U-joint, you should hear a dull sound when changing gears. A clicking sound indicates insufficient grease in the bearing. If you hear or feel vibrations when shifting gears, you may need to service the bearings to prolong their life.
it has a slide-in tube
The telescopic design is a modern alternative to traditional driveshaft designs. This innovative design is based on an unconventional design philosophy that combines advances in material science and manufacturing processes. Therefore, they are more efficient and lighter than conventional designs. Slide-in tubes are a simple and efficient design solution for any vehicle application. Here are some of its benefits. Read on to learn why this type of shaft is ideal for many applications.
The telescopic drive shaft is an important part of the traditional automobile transmission system. These driveshafts allow linear motion of the two components, transmitting torque and rotation throughout the vehicle’s driveline. They also absorb energy if the vehicle collides. Often referred to as foldable driveshafts, their popularity is directly dependent on the evolution of the automotive industry.
It uses a bearing press to replace worn or damaged U-joints
A bearing press is a device that uses a rotary press mechanism to install or remove worn or damaged U-joints from a drive shaft. With this tool, you can replace worn or damaged U-joints in your car with relative ease. The first step involves placing the drive shaft in the vise. Then, use the 11/16″ socket to press the other cup in far enough to install the clips. If the cups don’t fit, you can use a bearing press to remove them and repeat the process. After removing the U-joint, use a grease nipple Make sure the new grease nipple is installed correctly.
Worn or damaged U-joints are a major source of driveshaft failure. If one of them were damaged or damaged, the entire driveshaft could dislocate and the car would lose power. Unless you have a professional mechanic doing the repairs, you will have to replace the entire driveshaft. Fortunately, there are many ways to do this yourself.
If any of these warning signs appear on your vehicle, you should consider replacing the damaged or worn U-joint. Common symptoms of damaged U-joints include rattling or periodic squeaking when moving, rattling when shifting, wobbling when turning, or rusted oil seals. If you notice any of these symptoms, take your vehicle to a qualified mechanic for a full inspection. Neglecting to replace a worn or damaged u-joint on the driveshaft can result in expensive and dangerous repairs and can cause significant damage to your vehicle.
editor by CX 2023-04-03
China Auto Spare Parts Spline Shaft No. My-S10 Used for Mitsubishi Truck Automobile Rear Axle Agriculture Drive Shaft drive shaft coupling
Product Description
Merchandise Description
Vans.Drive Shaft
Generate shaft product NO . MY-S10
Product NO . |
H(Hole) | L(Duration) (mm) |
Z(Amount of teeth) |
Solution title | rear axle generate shaft |
Materials | 40cr carbon steel |
Gap | eight |
Duration | 835(mm) |
Variety of enamel | z=18 |
Top quality | Substantial performance |
Purpose of push shaft | Electricity transmission |
Automobile model of drive shaft | MITSUBISHI |
Processing of shaft | Forging |
Area treatment of shaft | Generally black customizable Silver, Blue, Rose Gold |
Availability | Can be tailored in accordance to drawings |
We also sell chassis add-ons for automobiles, trucks, agricultural machinery and construction machinery, which includes:
CVJ,Push shaft, steering drive shaft, differential components and assemblies, ball joints, common joints, tire screws, and so on
Organization Profile
FAQ
Q:Can you do OEM and supply samples firstly?
A:Of course,OEM and ODM are welcomed ,and with stocks ,samples can be delivered with 3 HangZhou as you need to have.
Q:What is the MOQ?payment term? and shipping and delivery time
A:For normal products, MOQ: 100PCS every single design
Once we get payment, we will ship your get within twenty doing work days.
The normal shipping and delivery time is 20days, dependent on which nation you are in.
Q:In which are you? Can we check out your manufacturing unit?
A:Our manufacturing unit is found in HangZhou, ZheJiang , China.
lt is close to HangZhou Airport, and the traffic at the west exit of HangZhou Sanquan Expressway is quite practical.
All staff of the business sincerely welcome domestic and foreign retailers to go to our company for guidance and enterprise negotiation.
US $15-100 / Piece | |
100 Pieces (Min. Order) |
###
Material: | Carbon Steel |
---|---|
Load: | Drive Shaft |
Stiffness & Flexibility: | Stiffness / Rigid Axle |
Journal Diameter Dimensional Accuracy: | IT6-IT9 |
Axis Shape: | Straight Shaft |
Shaft Shape: | Real Axis |
###
Samples: |
US$ 50/Piece
1 Piece(Min.Order) |
---|
###
Customization: |
Available
|
---|
###
Product NO . |
H(Hole) | L(Length) (mm) |
Z(Number of teeth) |
###
Product name | rear axle drive shaft |
Material | 40cr carbon steel |
Hole | 8 |
Length | 835(mm) |
Number of teeth | z=18 |
Quality | High performance |
Function of drive shaft | Power transmission |
Vehicle model of drive shaft | MITSUBISHI |
Processing of shaft | Forging |
Surface treatment of shaft | Usually black customizable Silver, Blue, Rose Gold |
Availability | Can be customized according to drawings |
US $15-100 / Piece | |
100 Pieces (Min. Order) |
###
Material: | Carbon Steel |
---|---|
Load: | Drive Shaft |
Stiffness & Flexibility: | Stiffness / Rigid Axle |
Journal Diameter Dimensional Accuracy: | IT6-IT9 |
Axis Shape: | Straight Shaft |
Shaft Shape: | Real Axis |
###
Samples: |
US$ 50/Piece
1 Piece(Min.Order) |
---|
###
Customization: |
Available
|
---|
###
Product NO . |
H(Hole) | L(Length) (mm) |
Z(Number of teeth) |
###
Product name | rear axle drive shaft |
Material | 40cr carbon steel |
Hole | 8 |
Length | 835(mm) |
Number of teeth | z=18 |
Quality | High performance |
Function of drive shaft | Power transmission |
Vehicle model of drive shaft | MITSUBISHI |
Processing of shaft | Forging |
Surface treatment of shaft | Usually black customizable Silver, Blue, Rose Gold |
Availability | Can be customized according to drawings |
How to Replace the Drive Shaft
Several different functions in a vehicle are critical to its functioning, but the driveshaft is probably the part that needs to be understood the most. A damaged or damaged driveshaft can damage many other auto parts. This article will explain how this component works and some of the signs that it may need repair. This article is for the average person who wants to fix their car on their own but may not be familiar with mechanical repairs or even driveshaft mechanics. You can click the link below for more information.
Repair damaged driveshafts
If you own a car, you should know that the driveshaft is an integral part of the vehicle’s driveline. They ensure efficient transmission of power from the engine to the wheels and drive. However, if your driveshaft is damaged or cracked, your vehicle will not function properly. To keep your car safe and running at peak efficiency, you should have it repaired as soon as possible. Here are some simple steps to replace the drive shaft.
First, diagnose the cause of the drive shaft damage. If your car is making unusual noises, the driveshaft may be damaged. This is because worn bushings and bearings support the drive shaft. Therefore, the rotation of the drive shaft is affected. The noise will be squeaks, dings or rattles. Once the problem has been diagnosed, it is time to repair the damaged drive shaft.
Professionals can repair your driveshaft at relatively low cost. Costs vary depending on the type of drive shaft and its condition. Axle repairs can range from $300 to $1,000. Labor is usually only around $200. A simple repair can cost between $150 and $1700. You’ll save hundreds of dollars if you’re able to fix the problem yourself. You may need to spend a few more hours educating yourself about the problem before handing it over to a professional for proper diagnosis and repair.
The cost of repairing a damaged driveshaft varies by model and manufacturer. It can cost as much as $2,000 depending on parts and labor. While labor costs can vary, parts and labor are typically around $70. On average, a damaged driveshaft repair costs between $400 and $600. However, these parts can be more expensive than that. If you don’t want to spend money on unnecessarily expensive repairs, you may need to pay a little more.
Learn how drive shafts work
While a car engine may be one of the most complex components in your vehicle, the driveshaft has an equally important job. The driveshaft transmits the power of the engine to the wheels, turning the wheels and making the vehicle move. Driveshaft torque refers to the force associated with rotational motion. Drive shafts must be able to withstand extreme conditions or they may break. Driveshafts are not designed to bend, so understanding how they work is critical to the proper functioning of the vehicle.
The drive shaft includes many components. The CV connector is one of them. This is the last stop before the wheels spin. CV joints are also known as “doughnut” joints. The CV joint helps balance the load on the driveshaft, the final stop between the engine and the final drive assembly. Finally, the axle is a single rotating shaft that transmits power from the final drive assembly to the wheels.
Different types of drive shafts have different numbers of joints. They transmit torque from the engine to the wheels and must accommodate differences in length and angle. The drive shaft of a front-wheel drive vehicle usually includes a connecting shaft, an inner constant velocity joint and an outer fixed joint. They also have anti-lock system rings and torsional dampers to help them run smoothly. This guide will help you understand the basics of driveshafts and keep your car in good shape.
The CV joint is the heart of the driveshaft, it enables the wheels of the car to move at a constant speed. The connector also helps transmit power efficiently. You can learn more about CV joint driveshafts by looking at the top 3 driveshaft questions
The U-joint on the intermediate shaft may be worn or damaged. Small deviations in these joints can cause slight vibrations and wobble. Over time, these vibrations can wear out drivetrain components, including U-joints and differential seals. Additional wear on the center support bearing is also expected. If your driveshaft is leaking oil, the next step is to check your transmission.
The drive shaft is an important part of the car. They transmit power from the engine to the transmission. They also connect the axles and CV joints. When these components are in good condition, they transmit power to the wheels. If you find them loose or stuck, it can cause the vehicle to bounce. To ensure proper torque transfer, your car needs to stay on the road. While rough roads are normal, bumps and bumps are common.
Common signs of damaged driveshafts
If your vehicle vibrates heavily underneath, you may be dealing with a faulty propshaft. This issue limits your overall control of the vehicle and cannot be ignored. If you hear this noise frequently, the problem may be the cause and should be diagnosed as soon as possible. Here are some common symptoms of a damaged driveshaft. If you experience this noise while driving, you should have your vehicle inspected by a mechanic.
A clanging sound can also be one of the signs of a damaged driveshaft. A ding may be a sign of a faulty U-joint or center bearing. This can also be a symptom of worn center bearings. To keep your vehicle safe and functioning properly, it is best to have your driveshaft inspected by a certified mechanic. This can prevent serious damage to your car.
A worn drive shaft can cause difficulty turning, which can be a major safety issue. Fortunately, there are many ways to tell if your driveshaft needs service. The first thing you can do is check the u-joint itself. If it moves too much or too little in any direction, it probably means your driveshaft is faulty. Also, rust on the bearing cap seals may indicate a faulty drive shaft.
The next time your car rattles, it might be time for a mechanic to check it out. Whether your vehicle has a manual or automatic transmission, the driveshaft plays an important role in your vehicle’s performance. When one or both driveshafts fail, it can make the vehicle unsafe or impossible to drive. Therefore, you should have your car inspected by a mechanic as soon as possible to prevent further problems.
Your vehicle should also be regularly lubricated with grease and chain to prevent corrosion. This will prevent grease from escaping and causing dirt and grease to build up. Another common sign is a dirty driveshaft. Make sure your phone is free of debris and in good condition. Finally, make sure the driveshaft chain and cover are in place. In most cases, if you notice any of these common symptoms, your vehicle’s driveshaft should be replaced.
Other signs of a damaged driveshaft include uneven wheel rotation, difficulty turning the car, and increased drag when trying to turn. A worn U-joint also inhibits the ability of the steering wheel to turn, making it more difficult to turn. Another sign of a faulty driveshaft is the shuddering noise the car makes when accelerating. Vehicles with damaged driveshafts should be inspected as soon as possible to avoid costly repairs.
editor by czh 2022-12-19
China auto parts high quality DRIVE SHAFT AXLE SHAFT FOR HILUX REVO 2016 43430-0K070 drive shaft cv joint
Product: HILUX
Calendar year: 2005-2016
OE NO.: 43430-0K070
Automobile Fitment: Toyota
Dimension: OEM Dimension
Substance: Metal
Design Number: 43430-0K070
Guarantee: 1 Several years Years
Automobile Make: FOR HILUX REVO
Solution Name: axle shaft
Colour: black
Packing: yellow box
Payment: Paypal
Top quality: Substantial-Qualiy
MOQ: 10 pcs
Packaging Information: yellow box
Port: HangZhou
Sizzling SALE
Brand Name | ZTR | ||||
Models | FOR HILUX REVO 2016 | ||||
Product title | AXLE SHAFT | ||||
Car | FOR HILUX REVO 2016 | ||||
OEM | 43430-0K070 | ||||
Size | standard dimension | ||||
Standard | OEM quality | ||||
Guarantee | 1 a long time | ||||
MOQ | 50pcs | ||||
Delivery | within 30 times | ||||
Package | yellow box | ||||
Shipment | sea,air,express | ||||
Payment | T/T,L/C,Paypal |
PRODUCTS DETAILS Packing & Shipping
Our Company Other Solution FAQQ1. Are you trading organization or factoryA: we are invested factory with buying and selling organization Q2. what items does your organization supply for CZPT brand ?A: 1) Manage arm and ball joint ,tie rod stop ,rack conclude ,linkage .
2) Drive shaft ,cv joint ,and tripod joints 3) Wheel hub ,wheel bearing 4) Brake pads ,brake footwear ,brake caliper ,brake disc 5) Steering rack ,steering pump ,steering knuckle 6) Shock absorber 7) Motor mount 8) Clutch plate ,clutch cover 9) Ignition coil ,clock spring , 10) gas pump ,oil filter ,admirer belt ,timing belt ,tensioner pully. Q3. what is the MOQ for every itemsA: if the things we have inventory ,there is no limitation for moq ,and narmally MOQ as 10pcsis satisfactory. This autumn. do you give any guarantee to your merchandise ?A: Sure ,we have 1years quality promise . Only brake pad ,brake shoe ,enthusiast belt timingbelt is gurantee 50000KM . Q5. how does to manage your CZPT goods ?A: one. There is innovative tools,expert and complex workersin the manufacturing facility.
2.Manufacturing facility will have sample screening on quality prior to cargo. 3.Our QC(Good quality Control) will verify the top quality of each and every productbefore shipment. Q6. How prolonged for delivery time following spend deposit?A: ·Usually 5-twenty days. ·Some scorching revenue items have inventory. Q7. which nations around the world have you exported for CZPT brand ? A: ASIA: Iraq, Lebanon, UAE, Turkey, Malaysia, Vietnam, LAOS, Thailand ,Syria, Saudi Arabia EUROPE: Russia, Kazakhstan, turkmenistan , azerbaijan Ireland ,new celedonia , OCEANIA: Australia, Fiji, Kiribati, AMERICAS: Panama,Xihu (West Lake) Dis.by means of, Canada, , Peru, Chile, Paraguay,Guatemala, Barbados AFRICA: Nigeria, Angola, , Ghana, Egypt ,UgHangZhou ,Burkina faso,Libya ,Mozambique Q8. How can I pay out you?
A: Right after you confirm our PL,we will request you to pay. T/T(HSBC financial institution) and Paypal,Westem Union are the most normal we are utilizing.
Q9. What’s the purchase porcedure?
A: First of all, we will verify all the products particulars like the OEM amount, packing, amount, delivry moments by e-mails//whatsApp/, them we will send the industrial invoice to u. When we receive u thirty% deposirt,we will commence to generate the goods,following merchandise are concluded, we will deliver the merchandise photo to u or u occur in excess of inspection, soon after obtain u equilibrium, we will deliver the goods to u.
How to Replace the Drive Shaft
Several different functions in a vehicle are critical to its functioning, but the driveshaft is probably the part that needs to be understood the most. A damaged or damaged driveshaft can damage many other auto parts. This article will explain how this component works and some of the signs that it may need repair. This article is for the average person who wants to fix their car on their own but may not be familiar with mechanical repairs or even driveshaft mechanics. You can click the link below for more information.
Repair damaged driveshafts
If you own a car, you should know that the driveshaft is an integral part of the vehicle’s driveline. They ensure efficient transmission of power from the engine to the wheels and drive. However, if your driveshaft is damaged or cracked, your vehicle will not function properly. To keep your car safe and running at peak efficiency, you should have it repaired as soon as possible. Here are some simple steps to replace the drive shaft.
First, diagnose the cause of the drive shaft damage. If your car is making unusual noises, the driveshaft may be damaged. This is because worn bushings and bearings support the drive shaft. Therefore, the rotation of the drive shaft is affected. The noise will be squeaks, dings or rattles. Once the problem has been diagnosed, it is time to repair the damaged drive shaft.
Professionals can repair your driveshaft at relatively low cost. Costs vary depending on the type of drive shaft and its condition. Axle repairs can range from $300 to $1,000. Labor is usually only around $200. A simple repair can cost between $150 and $1700. You’ll save hundreds of dollars if you’re able to fix the problem yourself. You may need to spend a few more hours educating yourself about the problem before handing it over to a professional for proper diagnosis and repair.
The cost of repairing a damaged driveshaft varies by model and manufacturer. It can cost as much as $2,000 depending on parts and labor. While labor costs can vary, parts and labor are typically around $70. On average, a damaged driveshaft repair costs between $400 and $600. However, these parts can be more expensive than that. If you don’t want to spend money on unnecessarily expensive repairs, you may need to pay a little more.
Learn how drive shafts work
While a car engine may be one of the most complex components in your vehicle, the driveshaft has an equally important job. The driveshaft transmits the power of the engine to the wheels, turning the wheels and making the vehicle move. Driveshaft torque refers to the force associated with rotational motion. Drive shafts must be able to withstand extreme conditions or they may break. Driveshafts are not designed to bend, so understanding how they work is critical to the proper functioning of the vehicle.
The drive shaft includes many components. The CV connector is one of them. This is the last stop before the wheels spin. CV joints are also known as “doughnut” joints. The CV joint helps balance the load on the driveshaft, the final stop between the engine and the final drive assembly. Finally, the axle is a single rotating shaft that transmits power from the final drive assembly to the wheels.
Different types of drive shafts have different numbers of joints. They transmit torque from the engine to the wheels and must accommodate differences in length and angle. The drive shaft of a front-wheel drive vehicle usually includes a connecting shaft, an inner constant velocity joint and an outer fixed joint. They also have anti-lock system rings and torsional dampers to help them run smoothly. This guide will help you understand the basics of driveshafts and keep your car in good shape.
The CV joint is the heart of the driveshaft, it enables the wheels of the car to move at a constant speed. The connector also helps transmit power efficiently. You can learn more about CV joint driveshafts by looking at the top 3 driveshaft questions
The U-joint on the intermediate shaft may be worn or damaged. Small deviations in these joints can cause slight vibrations and wobble. Over time, these vibrations can wear out drivetrain components, including U-joints and differential seals. Additional wear on the center support bearing is also expected. If your driveshaft is leaking oil, the next step is to check your transmission.
The drive shaft is an important part of the car. They transmit power from the engine to the transmission. They also connect the axles and CV joints. When these components are in good condition, they transmit power to the wheels. If you find them loose or stuck, it can cause the vehicle to bounce. To ensure proper torque transfer, your car needs to stay on the road. While rough roads are normal, bumps and bumps are common.
Common signs of damaged driveshafts
If your vehicle vibrates heavily underneath, you may be dealing with a faulty propshaft. This issue limits your overall control of the vehicle and cannot be ignored. If you hear this noise frequently, the problem may be the cause and should be diagnosed as soon as possible. Here are some common symptoms of a damaged driveshaft. If you experience this noise while driving, you should have your vehicle inspected by a mechanic.
A clanging sound can also be one of the signs of a damaged driveshaft. A ding may be a sign of a faulty U-joint or center bearing. This can also be a symptom of worn center bearings. To keep your vehicle safe and functioning properly, it is best to have your driveshaft inspected by a certified mechanic. This can prevent serious damage to your car.
A worn drive shaft can cause difficulty turning, which can be a major safety issue. Fortunately, there are many ways to tell if your driveshaft needs service. The first thing you can do is check the u-joint itself. If it moves too much or too little in any direction, it probably means your driveshaft is faulty. Also, rust on the bearing cap seals may indicate a faulty drive shaft.
The next time your car rattles, it might be time for a mechanic to check it out. Whether your vehicle has a manual or automatic transmission, the driveshaft plays an important role in your vehicle’s performance. When one or both driveshafts fail, it can make the vehicle unsafe or impossible to drive. Therefore, you should have your car inspected by a mechanic as soon as possible to prevent further problems.
Your vehicle should also be regularly lubricated with grease and chain to prevent corrosion. This will prevent grease from escaping and causing dirt and grease to build up. Another common sign is a dirty driveshaft. Make sure your phone is free of debris and in good condition. Finally, make sure the driveshaft chain and cover are in place. In most cases, if you notice any of these common symptoms, your vehicle’s driveshaft should be replaced.
Other signs of a damaged driveshaft include uneven wheel rotation, difficulty turning the car, and increased drag when trying to turn. A worn U-joint also inhibits the ability of the steering wheel to turn, making it more difficult to turn. Another sign of a faulty driveshaft is the shuddering noise the car makes when accelerating. Vehicles with damaged driveshafts should be inspected as soon as possible to avoid costly repairs.
editor by czh
China Standard Froging Bevel Gear Differential Parts Side Drive Gear Axle Shaft near me supplier
Merchandise Description
Hot forging elements for sell, we can make forging for auto part, machine areas, tractor areas and other individuals.
We have forging device from 2000ton to 8000ton, CZPT to end 50kgs goods
We can function in 40Cr, forty five#C, 20CrMnTi, 35Mn and other materils as for every your demands.
We can make forging according your samples or drawings.
How to Discover a Defective Push Shaft
The most typical difficulties associated with automotive driveshafts contain clicking and rubbing noises. Even though driving, the sound from the driver’s seat is usually visible. An seasoned auto mechanic can easily identify no matter whether the audio is coming from both sides or from one particular aspect. If you recognize any of these indications, it truly is time to ship your automobile in for a appropriate diagnosis. This is a guide to deciding if your car’s driveshaft is defective:
Symptoms of Driveshaft Failure
If you are possessing trouble turning your automobile, it is time to verify your vehicle’s driveshaft. A undesirable driveshaft can restrict the total management of your automobile, and you need to correct it as before long as attainable to avoid additional difficulties. Other signs of a propshaft failure include unusual noises from below the motor vehicle and difficulty shifting gears. Squeaking from underneath the motor vehicle is an additional indication of a defective driveshaft.
If your driveshaft fails, your auto will cease. Although the engine will nonetheless run, the wheels will not change. You might hear peculiar noises from beneath the automobile, but this is a unusual symptom of a propshaft failure. Even so, you will have plenty of time to repair the issue. If you will not hear any sound, the dilemma is not influencing your vehicle’s ability to shift.
The most obvious signs of a driveshaft failure are boring sounds, squeaks or vibrations. If the generate shaft is unbalanced, it is likely to harm the transmission. It will demand a trailer to take away it from your automobile. Aside from that, it can also impact your car’s functionality and demand repairs. So if you hear these indications in your automobile, be certain to have it checked by a mechanic proper absent.
Generate shaft assembly
When developing a propshaft, the layout ought to be based on the torque essential to drive the motor vehicle. When this torque is also higher, it can result in irreversible failure of the push shaft. For that reason, a good travel shaft layout ought to have a prolonged service existence. Here are some suggestions to support you design and style a very good driveshaft. Some of the principal components of the driveshaft are detailed underneath.
Snap Ring: The snap ring is a removable part that secures the bearing cup assembly in the yoke cross hole. It also has a groove for finding the snap ring. Spline: A spline is a patented tubular machined element with a series of ridges that suit into the grooves of the mating piece. The bearing cup assembly consists of a shaft and stop fittings.
U-joint: U-joint is essential because of to the angular displacement between the T-shaped housing and the pinion. This angle is especially big in elevated 4x4s. The design and style of the U-joint should assure a continuous rotational pace. Suitable driveshaft style have to account for the big difference in angular velocity amongst the shafts. The T-bracket and output shaft are connected to the bearing caps at each ends.
U-joint
Your automobile has a set of U-joints on the driveshaft. If your automobile wants to be changed, you can do it oneself. You will require a hammer, ratchet and socket. In purchase to eliminate the U-joint, you must first remove the bearing cup. In some circumstances you will want to use a hammer to remove the bearing cup, you should be careful as you don’t want to hurt the push shaft. If you are not able to remove the bearing cup, you can also use a vise to push it out.
There are two kinds of U-joints. 1 is held by a yoke and the other is held by a c-clamp. A entire ring is safer and best for automobiles that are usually utilized off-street. In some cases, a entire circle can be utilized to mend a c-clamp u-joint.
In addition to abnormal torque, extreme loads and inappropriate lubrication are frequent causes of U-joint failure. The U-joint on the driveshaft can also be broken if the engine is modified. If you are driving a motor vehicle with a greatly modified engine, it is not adequate to exchange the OE U-joint. In this scenario, it is crucial to consider the time to appropriately lubricate these factors as essential to keep them useful.
tube yoke
QU40866 Tube Yoke is a common replacement for ruined or destroyed driveshaft tubes. They are desirably manufactured of a metallic material, this sort of as an aluminum alloy, and consist of a hollow part with a lug structure at one particular end. Tube yokes can be manufactured making use of a assortment of approaches, including casting and forging. A typical technique entails drawing solid factors and machining them into the closing condition. The ensuing elements are considerably less pricey to produce, especially when in contrast to other kinds.
The tube fork has a relationship stage to the driveshaft tube. The lug structure supplies attachment points for the gimbal. Typically, the driveshaft tube is 5 inches in diameter and the lug construction is 4 inches in diameter. The lug construction also serves as a mounting stage for the drive shaft. After put in, Tube Yoke is effortless to keep. There are two varieties of lug constructions: one particular is solid tube yoke and the other is welded.
Heavy-duty series travel shafts use bearing plates to secure the yoke to the U-joint. All other dimensions are secured with external snap rings. Yokes are usually machined to accept U-bolts. For some purposes, grease fittings are employed. This attachment is much more ideal for off-road automobiles and functionality automobiles.
finish yoke
The end yoke of the drive shaft is an integral component of the push practice. Picking a high-high quality stop yoke will aid make sure long-time period operation and avoid premature failure. Pat’s Driveline provides a full line of automotive finish yokes for electricity just take-offs, differentials and auxiliary tools. They can also evaluate your current areas and provide you with higher good quality replacements.
A U-bolt is an industrial fastener with threaded legs. When utilized on a driveshaft, it provides higher stability in unstable terrain. You can purchase a U-bolt package to secure the pinion carrier to the push shaft. U-bolts also come with lock washers and nuts. Efficiency automobiles and off-road vehicles typically use this sort of attachment. But prior to you put in it, you have to make certain the yoke is machined to take it.
Finish yokes can be produced of aluminum or steel and are made to supply energy. It also offers particular bolt types for various programs. CZPT’s drivetrain is also stocked with a entire line of automotive flange yokes. The business also makes custom flanged yokes for a lot of well-known makes. Considering that the company has a complete line of replacement flange yokes, it can assist you remodel your drivetrain from non-serviceable to serviceable.
bushing
The very first phase in repairing or changing an automotive driveshaft is to change worn or broken bushings. These bushings are found inside of the travel shaft to provide a smooth, risk-free ride. The shaft rotates in a rubber sleeve. If a bushing needs to be changed, you must initial check the guide for recommendations. Some of these components may also require to be replaced, such as the clutch or swingarm.
China factory BT50 2012- RH CV Joint Axle Auto Parts Front Axle Shaft Drive Shaft for MAZDA with Good quality
Product: BT-50
Yr: 2006-2016, 2011-2015, 2015-2016, 2011-2016, 2006-2015
OE NO.: BT50 2012- RH
Automobile Fitment: Mazda
Dimensions: 66.5*26.00*13.50CM
Content: 40cr
Design Variety: UF97-25-60X-LH
Guarantee: 1 Many years
Vehicle Make: for MAZDA
Portion Title: Push shaft
MOQ: 2PCS
Placement on Vehicle: Front AXLE Appropriate
Sample: Accpet
High quality: 100% Expert Examination
OEM NO: BT50 2012- RH
Packaging Particulars: Package Kind:GEENTI Brand Package deal/Neutral Package/As Customers’ Request
BT50 2012- RH CV Joint Axle Vehicle Elements Front Axle Shaft Generate Shaft for MAZDA
Product Data
Part Title
CV Joint Axle Entrance Right Travel SHAFT
Software
FOR MAZDA BT50
Part Amount
BT50-2012-RH
OTHER Part Number
UF97-twenty five-50X-RH BT-fifty-twelve-R
Placement on Motor vehicle
Front AXLE Right
Abdominal muscles RING
With no
Materials
40cr
Warranty
one Yr
Sample
Accpet
Price
Welcome to inquiry the newest value
Place of origin
HangZhou
Shipping and delivery time
1-7 days for stock objects, 30 days for creation things
MOQ
two PCS
Packing
GEENTI Brand name Packing, Neutral Packing,As Customers’ Ask for
BOX/QTY
1PCS/BOX 2PCS /CTNS
Payment
L/C,T/T,Western Union,MoneyGram,PayPal
Solution Information
Top Merchandise
Company Info
Packaging & Shipping and delivery
Payment
FAQ
1. How a lot of several years is your business in vehicle areas company area?
A: Our Organization started because 2003, there is about sixteen several years historical past for us in vehicle areas organization subject.
Q2. Are you investing company or manufacturing unit?
A: We are factory with buying and selling business.
Q3. What products does your organization supply?
A: 1. Motor Areas:crankshaft,camshaft, connecting rod,cylinder head,cylinder head bolt,gasoline pump,oil pump,fuel injector,piston,h2o pump,timing belt,tensioner & pulley,gasket kit,engine mount,etc
two. Suspension Parts: shock absorber, coil spring,control arm, strut mount.
three. Steering Elements: steering rack, Great value Nema 34 planetary gearbox for stepper motor electrical power steering pump,steering knuckle,ball joint,stabilizer hyperlink,tie rod end.
four. Transmission Parts: CV joint, generate shaft, CV joint internal bearing,universal joint,clutch disc,wheel hub bearing, wheel bearing.
five. Brake Elements: brake pad,brake shoe,brake caliper,brake disc,brake grasp cylinder,wheel cylinder.
This autumn. Which international locations have you exported?
A: ASIA:ASIA: UAE,Oman,Iraq, Lebanon, Turkey, Thailand, Malaysia, Indonesia, Vietnam, Cambodia, Myanmar, Iran, Kuwait, Bahrain, Jordan,Japan,Jamaica, Excavator SK60-5 SK60-6 SK60-8 SK140-8 SK70 SK55 swing reduction gearbox YR32W00002F1. Cuba, Brazil, Peru, Chile, Nigeria, Angola, South Africa, Ghana, Kenya, Tanzania, Cameroon, Mozambique, Zambia, Egypt, Algeria, Libya, Zimbabwe, Mauritius,and many others
Q5. Do you have agent for your brand name?
A: Indeed, they are UAE-Dubai,Oman, Nigeria. And also have warehouse in there.
Q6. What is the MOQ for each item?
A: Our enterprise way is place sales, if the objects we have stock, there is no limitation for MOQ, and generally MOQ as 1 carton appropriate.
Q7. What about the shipping time?
A:It’s about 1 to 7 days for the items have in stock, 1 week to 1 month for the merchandise need to have to be manufactured primarily based on your purchase.
Q8. Do you give any promise to your products?
A: Essentially, we have 1 year quality assure for GEENTI brand spare elements.
Q9. Do you have any certification?
A: Indeed, like ISO: 9001, TS16949.
Q10. What will you do for high quality criticism?
A: 1. we will react to customer inside 24 hrs.
two. If there is batch products top quality difficulty, we will go to your warehouse with our technicist directly to check out the merchandise and send you the high top quality goods achieve freely.
three.If there is a few amount of high quality difficulties, we will replenishment or refund money.
How to inform if your driveshaft wants replacing
What is the lead to of the unbalanced drive shaft? Unstable U-joint? Your automobile could make clicking noises even though driving. If you can hear it from equally sides, it may well be time to hand it over to the mechanic. If you are not positive, read through on to discover much more. Thankfully, there are many techniques to notify if your driveshaft needs changing.
unbalanced
An unbalanced driveshaft can be the supply of odd noises and vibrations in your motor vehicle. To resolve this difficulty, you should contact a skilled. You can attempt a quantity of things to repair it, like welding and modifying the excess weight. The subsequent are the most common techniques. In addition to the strategies earlier mentioned, you can use standardized weights to stability the driveshaft. These standardized weights are connected to the shaft by welders.
An unbalanced push shaft usually produces lateral vibrations for every revolution. This variety of vibration is usually triggered by a broken shaft, lacking counterweights, or a overseas item stuck on the travel shaft. On the other hand, torsional vibrations happen 2 times per revolution, and they are induced by shaft phase shifts. Lastly, essential pace vibration happens when the RPM of the generate shaft exceeds its rated potential. If you suspect a driveshaft issue, verify the adhering to:
Manually adjusting the imbalance of a travel shaft is not the best activity. To avoid the issues of guide balancing, you can pick to use standardized weights. These weights are set on the outer circumference of the travel shaft. The operator can manually situation the fat on the shaft with specific equipment, or use a robot. However, handbook balancers have several disadvantages.
unstable
When the angular velocity of the output shaft is not consistent, it is unstable. The angular velocity of the output shaft is .004 at ph = 29.5 and 1.9 at t = 1.9. The angular velocity of the intermediate shaft is not a dilemma. But when it really is unstable, the torque used to it is too significantly for the device. It may well be a great thought to check out the tension on the shaft.
An unstable generate shaft can trigger a whole lot of noise and mechanical vibration. It can lead to untimely shaft fatigue failure. CZPT scientific studies the effect of shaft vibration on the rotor bearing system. They investigated the result of flex coupling misalignment on the vibration of the rotor bearing system. They believe that the vibrational reaction has two elements: x and y. Nevertheless, this strategy has limited software in numerous circumstances.
Experimental outcomes display that the presence of cracks in the output shaft may mask the unbalanced excitation qualities. For example, the existence of superharmonic peaks on the spectrum is characteristic of cracks. The existence of cracks in the output shaft masks unbalanced excitation attributes that can not be detected in the transient reaction of the enter shaft. Determine 8 displays that the frequency of the rotor boosts at vital pace and decreases as the shaft passes the natural frequency.
Unreliable
If you are obtaining trouble driving your auto, chances are you’ve operate into an unreliable driveshaft. This type of drivetrain can cause the wheels to adhere or not flip at all, and also limit the general management of the auto. Whatsoever the purpose, these concerns need to be fixed as quickly as attainable. Below are some signs to appear for when diagnosing a driveshaft fault. Let us consider a closer look.
The initial symptom you may possibly notice is an unreliable travel shaft. You may possibly really feel vibrations, or hear noises beneath the automobile. Depending on the result in, it could be a broken joint or a damaged shaft. The good news is that driveshaft repairs are typically reasonably affordable and take much less time than a full drivetrain substitution. If you’re not certain what to do, CZPT has a guidebook to changing the U-connector.
A single of the most typical signs of an unreliable driveshaft is clanging and vibration. These seems can be caused by worn bushings, unfastened U-joints, or damaged heart bearings. This can lead to serious vibration and sounds. You can also come to feel these vibrations via the steering wheel or the floor. An unreliable driveshaft is a symptom of a greater problem.
Unreliable U-joints
A automobile with an unreliable U-joint on the generate shaft can be dangerous. A bad u-joint can avoid the automobile from driving effectively and could even result in you difficulties. Unreliable u-joints are cheap to change and you ought to try obtaining elements from good quality makers. Unreliable U-joints can trigger the automobile to vibrate in the chassis or equipment lever. This is a confident sign that your automobile has been neglected in servicing.
Replacing a U-joint is not a complex job, but it requires special instruments and a lot of elbow grease. If you do not have the correct instruments, or you happen to be unfamiliar with mechanical terminology, it really is very best to look for the assist of a mechanic. A specialist mechanic will be ready to correctly evaluate the problem and propose an suitable resolution. But if you don’t truly feel self-confident ample, you can change your own U-connector by adhering to a number of easy actions.
To guarantee the vehicle’s driveshaft is not damaged, check out the U-joint for wear and lubrication. If the U-joint is worn, the steel parts are likely to rub towards each other, leading to use. The faster a issue is diagnosed, the more rapidly it can be settled. Also, the longer you wait around, the more you get rid of on repairs.
ruined push shaft
The driveshaft is the element of the car that connects the wheels. If the driveshaft is broken, the wheels might cease turning and the motor vehicle may sluggish down or cease relocating totally. It bears the weight of the auto by itself as properly as the load on the highway. So even a slight bend or break in the push shaft can have dire repercussions. Even a piece of loose metallic can turn out to be a deadly missile if dropped from a car.
If you hear a screeching sound or growl from your vehicle when shifting gears, your driveshaft could be ruined. When this transpires, hurt to the u-joint and abnormal slack in the generate shaft can outcome. These circumstances can additional hurt the drivetrain, like the entrance 50 %. You need to replace the driveshaft as shortly as you observe any signs and symptoms. Right after changing the driveshaft, you can begin searching for indicators of use.
A knocking seem is a indicator of damage to the drive shaft. If you listen to this seem although driving, it might be due to worn couplings, ruined propshaft bearings, or damaged U-joints. In some circumstances, the knocking noise can even be brought on by a ruined U-joint. When this happens, you could require to change the whole driveshaft, necessitating a new one.
Upkeep expenses
The expense of fixing a driveshaft varies commonly, relying on the variety and cause of the dilemma. A new driveshaft expenses in between $three hundred and $1,three hundred, which includes labor. Restoring a broken driveshaft can value anyplace from $two hundred to $three hundred, based on the time needed and the sort of components required. Indicators of a broken driveshaft include unresponsiveness, vibration, chassis sounds and a stationary car.
The 1st point to consider when estimating the value of restoring a driveshaft is the kind of motor vehicle you have. Some automobiles have far more than 1, and the areas utilized to make them may not be compatible with other vehicles. Even if the exact same car has two driveshafts, the broken types will value far more. Luckily, numerous automobile mend retailers supply totally free quotes to fix damaged driveshafts, but be conscious that these kinds of perform can be difficult and pricey.